Buyer planning guide
Display Fridge Size: Cabinet Height and Total Countertop Height
Compare five JINYU countertop display fridges and calculate floor-to-top height from your measured counter. Includes overhead-space examples and a site worksheet.

Five cabinets: recorded dimensions and calculated top heights
| JINYU model | W × D × H (mm) | Listed capacity | Top above floor on 850 mm counter | Top above floor on 900 mm counter | Top above floor on 950 mm counter |
|---|---|---|---|---|---|
| GN-660RT | 660 × 530 × 730 mm | 102 L | 1580 mm | 1630 mm | 1680 mm |
| GN-900RT | 900 × 530 × 730 mm | 140 L | 1580 mm | 1630 mm | 1680 mm |
| GN-1200RT | 1200 × 530 × 730 mm | 190 L | 1580 mm | 1630 mm | 1680 mm |
| GN-900CT | 900 × 530 × 730 mm | 120 L | 1580 mm | 1630 mm | 1680 mm |
| GN-1200CT | 1200 × 530 × 730 mm | 162 L | 1580 mm | 1630 mm | 1680 mm |
Worked overhead example: underside at 1800 mm
| Example counter height | Cabinet top above floor | Gap to 1800 mm underside |
|---|---|---|
| 850 mm | 1580 mm | 220 mm |
| 900 mm | 1630 mm | 170 mm |
| 950 mm | 1680 mm | 120 mm |
Countertop height inquiry worksheet
| Record | Buyer supplies | Requested response or reference |
|---|---|---|
| Floor reference | Finished-floor level on customer and staff sides | Reference used for every elevation measurement |
| Supporting surface | Measured height, width and depth; drawing revision | Cabinet base arrangement and equipment-weight definition |
| Cabinet outline | Selected RT or CT model and intended position | Exact W × D × H and installation drawing |
| Overhead objects | Underside height, depth and lowest projecting fitting | Required installation spacing for the offered configuration |
| Viewing trial | Recorded standing positions and intended product view | Model profile and selected display level |
| Serving trial | Tray or board dimensions, staff position and destination | Shelf positions, clear opening and access demonstration |
Does display fridge height include the counter underneath?
The listed height describes the cabinet. For a countertop display, add the height of the supporting surface above the finished floor to find the cabinet top position. JINYU GN-660RT, GN-900RT and GN-1200RT each list a 730 mm cabinet height. On an illustrative 900 mm-high counter, the cabinet top is 900 + 730 = 1630 mm above the floor. Measure your own counter before using that calculation.
Write both figures on the elevation drawing: cabinet height and floor-to-cabinet-top height. Keep the floor reference beside the measurement, especially when the customer and staff stand on different floor levels. A display selected from a 730 mm catalog entry can occupy a much taller part of the room once placed on furniture. The calculation identifies its top position; it does not establish viewing comfort or installation spacing.
Which countertop models share the same height but different widths?
The RT range here includes GN-660RT at 660 × 530 × 730 mm, GN-900RT at 900 × 530 × 730 mm and GN-1200RT at 1200 × 530 × 730 mm. Their listed capacities are 102 L, 140 L and 190 L. The curved-front alternatives GN-900CT and GN-1200CT measure 900 × 530 × 730 mm and 1200 × 530 × 730 mm, with 120 L and 162 L capacities respectively.
All five therefore produce the same calculated top height on a shared supporting surface. Increasing width from 660 to 1200 mm adds 540 mm of cabinet frontage while leaving that height calculation unchanged. Compare width, glass profile and capacity as separate selection fields. A shared exterior height does not supply shelf clear heights, loading-opening dimensions or equipment weight. Request those measurements against the exact model you shortlist.
How does a different counter height change the display position?
For the same 730 mm cabinet, example supporting surfaces at 850, 900 and 950 mm place the cabinet top at 1580, 1630 and 1680 mm above the floor. These three counter heights are arithmetic examples, not recommended furniture dimensions. Moving the supporting surface upward by 50 mm moves the cabinet top upward by the same amount. The comparison table keeps the three site examples separate from the recorded cabinet specification.
Measure to the actual surface carrying the cabinet. If a project drawing includes a raised platform or a separate plinth, identify whether its top is already included in that surface measurement. Record any proposed base arrangement in the installation drawing. After a furniture revision, repeat the floor-to-support measurement and update the elevation. Reusing the original counter dimension after a platform has changed would leave the display shown at the wrong height.
How can I compare the cabinet top with an overhead shelf?
Measure the lowest underside of the overhead object from the same finished-floor reference. In an illustrative layout, an underside at 1800 mm and a cabinet top at 1630 mm leave a vertical arithmetic balance of 170 mm. With the 950 mm example counter, the cabinet top is 1680 mm and the balance becomes 120 mm. Label these as measured geometric gaps. Obtain the installation instructions to establish the spacing required for the offered configuration.
Draw the shelf depth and cabinet depth in side view as well. An overhead shelf that projects across the staff access area creates a different arrangement from one that ends behind it. Add light fittings, brackets and other low projections to the drawing with their own underside heights. Use the lowest relevant obstruction in each location, retaining the wider view and close measurement photograph so the reviewer can identify where the gap was taken.
How should staff and customer sightlines be reviewed?
Prepare a side elevation with the proposed cabinet outline, customer standing position, staff position and any till or pickup point. Mark the counter surface and cabinet top using the same floor reference. For the actual people reviewing the arrangement, record the viewing positions used in the trial. A 1630 mm calculated top height gives a location to draw; it cannot establish whether a person can see the intended product or communicate across the counter.
Use a full-size outline or a site mockup to review those views before finalising the furniture. Photograph the intended product-view direction from each recorded position. Keep the CT curved profile or RT straight profile identified, because matching outside dimensions alone do not describe the glass shape. Record which display level or handover point the viewer was trying to see, then repeat the same views if the cabinet or supporting surface changes.
Does a comfortable viewing height also establish serving access?
Review serving as a separate sequence. These RT and CT records describe rear sliding doors. Show the staff side on the plan, identify the intended shelf level and use the actual tray, board or serving dish dimensions when requesting a loading demonstration. The overall 730 mm cabinet height provides no measurement of the opening or the distance from the supporting surface to a particular shelf.
Ask for a model-specific drawing showing shelf positions and clear opening dimensions. In a site trial, record the staff standing position, the object removed and its destination on the packing surface. Keep those observations with the elevation used for the height comparison. A change in counter height affects the position of the whole cabinet, while a change in shelf arrangement affects the task inside it. Track both revisions when the proposed serving sequence is reviewed.
What measurements should go into a countertop display size inquiry?
Send the full JINYU model code, measured counter width and depth, floor-to-support height and overhead underside heights. Include a front elevation, side elevation and staff-side plan with matching position labels. State which floor each vertical measurement uses. Attach the product dimensions and the viewing or serving task that needs review. The worksheet below provides a compact record for those inputs and the requested model-specific response.
Ask for the offered configuration's installation drawing, base arrangement, equipment weight definition and usable loading measurements. Keep the cabinet data and the site measurements in separate columns. Once the response identifies the actual installation arrangement, revise the floor-to-top calculation if the supporting arrangement changes and retain that revision with the furniture drawing.
Reference sources
- Compare countertop cabinet widths and capacities
- Choose display fridge dimensions for your site
- Review countertop weight and the supporting surface
- Compare straight glass RT models
- Compare curved glass CT models
Regional references support general planning; model-specific specifications come from the published JINYU model tables.