Skip to content
JINYUCOMMERCIAL KITCHEN EQUIPMENT
Menu

Buyer planning guide

Display Fridge Size for Round Cake Boards: Diameter and Shelf Layout

Compare cake and board diameters with three illustrative circle layouts, real JINYU cabinet sizes and a shelf-by-shelf loading and removal review.

JINYU GN-1200RT straight-glass countertop cake display on a cafe counter

Round boards in an illustrative 800 × 400 mm rectangle

These buyer examples use aligned rows with no spacing allowance. The rectangle is hypothetical and is not a JINYU shelf specification. Counts describe outline positions, before checking obstructions, loading and removal.

Positions = whole boards across × whole rows deep; use the complete assembly diameter if it exceeds the board.
Cake diameterBoard diameterAcrossRows deepOutline positionsUnused width / depth
150 mm200 mm4280 / 0 mm
200 mm250 mm31350 / 150 mm
250 mm300 mm212200 / 100 mm

Outside cabinet sizes for the initial shortlist

Recorded cabinet specifications; request usable shelf dimensions for each model.
ModelW × D × H (mm)Listed capacityInstallation
GN-900CT900 × 530 × 730120 LCountertop
GN-1200RT1200 × 530 × 730190 LCountertop
GN-1200RF21200 × 730 × 1200425 LFreestanding

Record the calculation and the observed arrangement separately

For each level, record: model and drawing revision; usable outline; board identifiers and complete diameters; assembled heights; proposed centre positions; calculated count; demonstrated count; removal observations; photograph or video reference.

Send the cabinet shortlist and measured board register →

Which diameter should I use when choosing a display fridge size for whole cakes?

Use the widest part of the complete display assembly. Measure the cake, board, stand and cover separately, then record the largest outside diameter and complete standing height. A cake described as 200 mm can sit on a 250 mm board. In that arrangement, the board sets the horizontal outline. Decorations or a dome can extend beyond it, so measure the assembled item in the condition used for display.

Give each assembly an identifier and photograph it from above and from the side. Keep the measured diameter beside the cake description instead of using the cake name as a size. For a mixed assortment, record each board separately. This lets the cabinet response address the actual objects entering the display and gives staff a consistent reference when checking a replacement board.

How much can a larger cake board change a shelf layout?

Consider an illustrative loading rectangle measuring 800 × 400 mm. A simple aligned grid of 200 mm circles has four positions across and two rows deep, giving eight outline positions. Increasing the diameter to 250 mm gives three across and one row deep: three positions. At 300 mm diameter, the same grid gives two positions across and one row deep.

These are calculations for a hypothetical rectangle, with no spacing or access allowance. They are not counts for a JINYU shelf. The worksheet compares three example cake-and-board combinations so that the diameter used in each calculation stays visible. Do not calculate from the smaller cake diameter and then load the larger boards. Use the result to choose a physical arrangement to review, keeping the observed count separate from the arithmetic.

Can circles be staggered to fit more cakes than an aligned grid?

An aligned grid is one arrangement, not a maximum-packing calculation. Staggering round boards changes the centre positions and the distance between rows. It can also change which cake must be moved before another can be removed. Draw the proposed centres on a measured shelf outline and use full-size paper circles or the actual boards to examine the arrangement.

Keep lights, supports, glass profiles and other obstructions on that drawing. A rectangular boundary cannot represent a curved or obstructed shelf at every depth. Record any spacing chosen for the trial and the reason it was chosen. Photograph the complete layout with the same board identifiers used in the assortment register. The purchasing comparison then has a visible arrangement to discuss, rather than a capacity figure derived from a different pattern.

Which JINYU cabinet sizes can I use to start the shortlist?

GN-900CT is a curved-glass countertop display measuring 900 × 530 × 730 mm, with 120 L listed capacity and two chrome-plated shelves. GN-1200RT is a straight-glass countertop display measuring 1200 × 530 × 730 mm, with 190 L and two raised shelves. GN-1200RF2 is a freestanding straight-glass cabinet measuring 1200 × 730 × 1200 mm, with 425 L and two glass shelves.

Use these outside measurements to locate each candidate on the site plan. Request usable width, usable depth and clear height for every intended display level on the offered configuration. The 800 × 400 mm rectangle in the calculation is independent of all three models. Neither their listed litres nor their exterior width supplies that internal rectangle. Keep the returned shelf drawing beside its complete model code before comparing the board arrangements.

How should I check removal through a sliding-door opening?

Identify the service-side opening used to load each cake. Request its clear width and height with the door in the loading position, including any fixed divider. Draw the route from the shelf to the staff work surface and show where hands support the board. The final resting position and the path through the opening are separate measurements.

Run a continuous removal sequence using the intended assembly and neighbouring boards. Start with the chosen display fully arranged, remove a middle item, then replace it. Record whether another item has to move, whether the cover is removed and where the assembly turns. Keep the shelf level and door position in view. A layout that fits as circles on paper still needs this task review before its count becomes the operating display target.

Can I multiply one shelf count by the number of shelves?

Measure and review each level separately. Shelf depths, clear heights and the usable outline can differ within a cabinet. Two listed shelves do not establish two identical loading rectangles. The lower display surface should have its own identifier and measurements if it is part of the proposed arrangement. Keep the assortment assigned to each level visible in the record.

Height matters independently of diameter. A board can fit horizontally while its decorated cake or dome meets an obstruction above. Record complete assembled height at the intended position, along with the shelf arrangement. Also request model-specific shelf-load information for the proposed contents. A geometric outline count contains no weight calculation and does not establish a permitted shelf load or a temperature result.

What should I send with a round-cake display inquiry?

Send the candidate model codes, site drawing and board register to JINYU, Shaanxi Jinyu Kitchenware Co., Ltd. (陕西金宇厨具有限公司). For each assembly, include cake diameter, board or stand diameter, complete outside diameter, assembled height and a photograph reference. Identify which levels need which assortment and attach the proposed circle layout with its dimensions and revision.

Ask the reply to connect usable shelf measurements, loading openings and a removal demonstration to the same model and configuration. If the proposed cabinet or board changes, update the affected layout rather than carrying forward its earlier count. Retain the calculated positions, demonstrated arrangement and selected operating quantity as distinct entries. This makes a fridge-size decision traceable from the objects being displayed through the cabinet documents to the actual serving task.

Reference sources

Regional references support general planning; model-specific specifications come from the published JINYU model tables.