Skip to content
JINYUCOMMERCIAL KITCHEN EQUIPMENT
Menu

Grab-and-go counter · model specification comparison

Grab-and-go counter temperature ranges: compare six JINYU models

Compare recorded 2-8°C and 0-10°C ranges across six JINYU grab-and-go display models, with cabinet sizes, customer access and a temperature-document request sheet.

Compare recorded ranges →
JINYU GN-1200L open-front grab-and-go chiller in a cafe or bakery
JINYU GN-1200L open-front counter: 1200 × 740 × 1400 mm, 295 L and a recorded range of 2-8°C.

Two catalogue ranges, six cabinet records

Dimensions are exterior W × D × H. The listed ranges and rated watts are model specifications; measured results belong in the separate document request below.

Recorded JINYU model specifications for low open-front displays and upright beverage coolers.
ModelTemperature rangeCustomer accessW × D × H (mm)CapacityShelvesRated power
GN-900L2-8 °COpen front900 × 740 × 1400 mm235 L2 shelves plus base deck820 W
GN-1200L2-8 °COpen front1200 × 740 × 1400 mm295 L2 shelves plus base deck950 W
GN-900LG2-8 °COpen front900 × 740 × 1350 mm200 L2 shelves plus base deck820 W
GN-1000FRO2-8 °COpen front1000 × 730 × 1300 mm390 L2 glass shelves plus base deck470 W
GN-620FS0-10°CHinged glass doors620 × 700 × 2018 mm410 L4 wire shelves210 W
GN-868FM0-10 °CHinged glass doors1220 × 690 × 2048 mm960 L4 shelves300 W

All six records list fan cooling, R290 refrigerant and 220-240V/50Hz supply.

What temperature ranges are listed for a grab-and-go counter?

The six models in this comparison fall into two recorded groups. GN-900L, GN-1200L, GN-900LG and GN-1000FRO list 2-8°C. The upright GN-620FS and GN-868FM beverage coolers list 0-10°C. Keep the range beside the complete model code when comparing proposals: the phrase grab-and-go counter covers several cabinet arrangements.

These are catalogue specifications, rather than measurements from your proposed location. Ask for the operating documentation for the offered configuration and identify the products you intend to display. Record any requested operating value separately from the catalogue range. That gives the equipment discussion a specific target without changing the published specification or implying that every point in a range suits every assortment.

Does a 0-10°C range make a beverage cooler interchangeable with a 2-8°C counter?

The ranges overlap, but the cabinet records describe different equipment. GN-620FS has a hinged glass door, four wire shelves and 410 L listed capacity. GN-868FM has two hinged glass doors, four shelves and 960 L. The four low open-front models in this table have two shelves plus a base deck and capacities from 200 to 390 L.

Compare access and the intended assortment alongside the temperature field. If a proposal substitutes an FS or FM beverage cooler for an L, LG or FRO display, request the replacement model documents and revise the shelf plan. An overlapping numerical range does not supply a model-specific assessment of your products, the usable shelf dimensions or the installation conditions.

How do I compare two open-front counters with the same width?

GN-900L and GN-900LG both measure 900 mm wide and 740 mm deep. Both list 2-8°C, 820 W rated power and two shelves plus a base deck. GN-900L is 1400 mm high with 235 L capacity; GN-900LG is 1350 mm high with 200 L. Their recorded heights differ by 50 mm and capacities by 35 L.

Their matching exterior footprints each occupy 0.666 square metres, calculated as 0.900 multiplied by 0.740. Keep the identical footprint and range in one comparison row, then assess the different heights, capacities and side-glass arrangement. Request usable shelf measurements for the selected model before assigning packs. The 35 L difference does not establish a difference in sandwich counts or bottle facings.

What changes when the shortlisted counter becomes wider or taller?

Within the L pair here, GN-1200L adds 300 mm of width over GN-900L. Depth remains 740 mm, height remains 1400 mm and the listed range remains 2-8°C. Capacity rises from 235 to 295 L and rated power from 820 to 950 W. A width substitution therefore changes several equipment-schedule fields even when the temperature entry stays the same.

The upright alternatives change the outline more substantially. GN-620FS measures 620 × 700 × 2018 mm; GN-868FM measures 1220 × 690 × 2048 mm. Put the full dimensions and door-opening drawing on the site plan. A narrower upright body can introduce a different loading approach and a higher top edge, so retain height and access in the review instead of sorting solely by width.

Can I rank these counters by cooling performance or energy use from this table?

The table records ranges and rated watts, with fan cooling, R290 refrigerant and 220-240V/50Hz supply listed for all six models. GN-1000FRO is rated at 470 W, compared with 820 W for GN-900L and GN-900LG. The FS and FM records list 210 W and 300 W respectively. Those figures identify the recorded electrical specifications.

The source records used here contain no matched daily energy test or temperature-distribution comparison across these cabinets. Request measured results with the exact model identity and test conditions if those are purchase criteria. Keep such evidence separate from rated watts and catalogue temperature ranges. A lower watt rating alone does not establish a lower daily electricity total in the intended shop.

Which temperature documents should I request with the model quotation?

Name the offered model and configuration on the document request. Ask for its operating instructions, controller instructions, installation requirements and any available model-specific temperature-test information. For a test report, request the tested cabinet identity, measurement positions, recorded values and stated test conditions together so the result remains attached to the equipment it describes.

Attach the proposed assortment and a location drawing, including nearby equipment and the customer approach. State the requested operating value as a buyer requirement rather than rewriting it into the catalogue range. Record the response beside each requested document in the worksheet. When a substitute model is offered, reopen those rows for the replacement rather than carrying over the first cabinet response.

How should shelf and access details stay connected to the temperature request?

Create one assortment row per container shape with its outside width, depth and height. Assign the proposed shelf and note whether a customer removes the item directly or staff hand it over. GN-1000FRO records two glass shelves plus a base deck; GN-900L, GN-1200L and GN-900LG record two shelves plus a base deck. The upright FS and FM models each record four shelves.

Request the usable shelf layout and loading instructions for that exact arrangement. Keep any proposed pack count as a buyer layout until the relevant measurements are available. Attach the same shelf-plan revision to the temperature-document request and quotation comparison. That links the products and cabinet layout under discussion without treating listed litres as an assortment plan.

What should a complete grab-and-go counter comparison inquiry contain?

Send Shaanxi Jinyu Kitchenware Co., Ltd. (陕西金宇厨具有限公司) the shortlisted model codes, requested quantities and destination. Include the full cabinet dimensions, intended assortment, requested operating value and site electrical supply. Add the floor plan, shelf-layout questions and the document request sheet so the reply can address the same scope for each candidate.

Keep the published range in its own column and place the requested configuration and returned evidence beside it. If a response changes the model, update the dimensions, capacity, shelf arrangement, access and rated power together. Retain the document revision with the proposal. This makes the final comparison traceable to a particular cabinet instead of leaving a generic grab-and-go description on the purchase brief.

Temperature and configuration document request sheet

Complete one sheet per shortlisted model and retain the returned document references with the quotation.
RecordBuyer inputRequested response
Cabinet identityFull model code and offered configurationModel-specific quotation and document revision
Catalogue rangeRecorded range from the selected modelMatching model specification
Requested operationBuyer requested operating value and intended assortmentResponse tied to that assortment and configuration
LocationSite plan, nearby equipment and electrical supplyInstallation requirements for the proposed cabinet
Shelf planPack dimensions, proposed shelves and access routeUsable shelf drawing and loading instructions
Temperature evidenceRequested measurements and document identityTested model, measurement positions, results and stated conditions
Configuration changeReplacement code and revised cabinet outlineUpdated range, shelf plan, access and electrical documents
Send shortlisted models and the document request →