Skip to content
JINYUCOMMERCIAL KITCHEN EQUIPMENT
Menu

Measured cabinet outlines

Display Fridge Size for a Right-Angle Corner: Two-Cabinet Layout

Compare two right-angle display fridge layouts using GN-900RT and GN-1200RF2: cabinet depth at the corner, leg lengths, counter height and service-side access.

Compare the two corner layouts →
JINYU GN-900RT straight glass cabinet on a cafe counter
JINYU GN-900RT countertop display. Supporting furniture has its own outline and height on the corner plan.

Two cabinet-only corner arrangements

Illustrative right-angle geometry, before furniture, installation spacing and working access. Both views use the same relative scale. Blue = GN-900RT; green = GN-1200RF2. Their front and service orientations must be reviewed for the actual site.

RTRF2900 × 1730 mm extent
A: RT occupies the corner first
RTRF21630 × 1200 mm extent
B: RF2 occupies the corner first
Outside cabinet dimensions. RT is countertop; RF2 is freestanding.
ModelW × D × H (mm)InstallationCapacity
GN-900RT900 × 530 × 730Countertop140 L
GN-1200RF21200 × 730 × 1200Freestanding425 L

Corner measurement worksheet

RecordMeasurement or document
Shared originCorner reference, horizontal usable length and vertical usable length
Cabinet positionsModel codes, corner offsets, front arrows and service sides
Supporting furnitureRT counter footprint, height, end panels and construction record
Installation overlayModel-specific spacing, service access and loading positions
Site evidencePhotographs from both legs, fixed obstructions and plan revision

Why do two cabinet widths underestimate a corner layout?

At a right-angle corner, one cabinet occupies part of the wall length used to position the other. Adding the two widths treats the arrangement as a straight line and loses this depth contribution. Draw both rectangles from one shared corner reference. Give each cabinet a width direction, depth direction and customer-facing edge. You can then identify where the outlines intersect before allocating installation space.

Use two actual JINYU models for the exercise: GN-900RT measures 900 × 530 × 730 mm and GN-1200RF2 measures 1200 × 730 × 1200 mm. RT is a countertop display; RF2 is freestanding. The diagrams compare their cabinet outlines in plan view. The counter supporting RT needs a separate outline and construction review. Neither arrangement below is an approved installation plan.

How is the first corner arrangement calculated?

Use an illustrative room corner with two perpendicular walls. Put the 900 mm width of GN-900RT along the horizontal wall, starting at the corner. Its 530 mm depth projects into the room. Rotate GN-1200RF2 by 90 degrees and place its width along the vertical wall, starting after the RT depth. RF2 then occupies 1200 mm beyond that 530 mm corner segment. The resulting cabinet-only extents are 900 mm horizontally and 1730 mm vertically.

The 1730 mm calculation is 530 + 1200. If both cabinets instead started at the same corner, their rectangles would overlap over 730 × 530 mm. That overlap is a drawing conflict, not usable display space. Moving RF2 past the RT depth removes the overlap in this simplified example. Installation spacing and the actual supporting furniture must still be added.

What changes when the freestanding cabinet takes the corner first?

Place GN-1200RF2 against the vertical wall starting at the corner. Its 730 mm depth now occupies the beginning of the horizontal leg. Put GN-900RT along the horizontal wall after that segment. The horizontal extent becomes 730 + 900 = 1630 mm, while the vertical extent is 1200 mm. This is the second arrangement in the diagram.

Compared with the first arrangement, the second uses 730 mm more horizontal extent and 530 mm less vertical extent. Both contain exactly the same cabinets. This is why a corner shortlist needs two leg measurements, with the arrangement named beside them. A single combined frontage cannot show which wall is the limiting one. Measure from the same physical corner in both alternatives.

Does the smaller bounding rectangle mean a better layout?

The first arrangement has a 900 × 1730 mm bounding rectangle; the second has a 1630 × 1200 mm bounding rectangle. Those outer rectangles include empty floor as well as cabinet outlines. They are useful for comparing maximum extents on a drawing, but their area is not the occupied cabinet area or an allowance for people. The cabinet rectangles total 0.477 + 0.876 = 1.353 square metres in either arrangement.

Show the unused space inside each outline separately. Then draw actual customer approaches and staff loading positions. Both models have service-side sliding doors. A cabinet placed against a wall in a geometric exercise can lose the access needed to load it. Reposition the rectangles using the model installation drawings and the intended serving direction before choosing a room layout.

How do I compare the two display heights at the corner?

GN-900RT stands 730 mm above its supporting surface. On an illustrative 900 mm-high counter, its top would be 1630 mm above the floor. GN-1200RF2 is freestanding and its listed overall height is 1200 mm. The cabinet tops in that example differ by 430 mm. Changing the counter height changes the RT elevation without changing its own cabinet dimensions.

Draw a separate elevation through each leg. Mark the actual measured counter height, cabinet top and nearby shelves. The two cabinet-top levels do not establish shelf elevations or the transfer height of a cake tray. Request those internal measurements for the selected configuration. Add the counter footprint to the plan, particularly if it extends beyond the RT cabinet or contains an end panel at the corner.

Which measurements belong in the corner inquiry?

Give the corner a site reference and record both usable wall lengths from that point. Mark skirting, columns, sockets, counter ends and fixed equipment. Photograph the corner from both approaches, then label the same objects on the plan. Include the cabinet codes and front-edge arrows so the reviewer can distinguish a rotated cabinet from a different model. Keep millimetres as the common drawing unit.

Attach the two alternative layouts with their calculated cabinet-only extents. Request the installation drawing, service access information and shelf dimensions for each selected model. Send the counter construction record for RT as a separate attachment. Address the inquiry to JINYU, Shaanxi Jinyu Kitchenware Co., Ltd. (陕西金宇厨具有限公司), and retain the revised layout with the matching configuration response. Packed delivery dimensions belong on the receiving-route sheet rather than replacing the cabinet rectangles.

How should I revise the drawing after moving one cabinet?

Keep the original corner reference and label each alternative with a revision. Update both leg extents whenever a cabinet moves, then redraw the counter and service positions affected by that change. Record the actual offset between cabinets as its own dimension. If a different model is proposed, replace its complete width, depth and height record together. Share the revised plan with the same people reviewing support, loading access and installation so their responses describe one arrangement.

Send the model shortlist and scale plan →