Buyer planning guide
Non-Woven Bag Size Chart: Inch Rounding and the Millimetre Master
Compare real JINYU bag sizes in cm, mm, decimal inches and eighth inches. See rounding differences for twelve dimensions and keep source sizes in your stock inquiry.

Four catalogue references in four unit displays
All dimension strings use width × height × depth. Original catalogue centimetres remain the source. Inches are converted using 1 inch = 25.4 mm; the two inch columns use different rounding methods.
| Style and variant | Catalogue cm | Source equivalent mm | Inches, two decimals | Inches, nearest eighth |
|---|---|---|---|---|
| Non-Woven Takeaway Bag · M | 23 × 25 × 14 cm | 230 × 250 × 140 | 9.06 × 9.84 × 5.51 | 9 × 9 7/8 × 5 1/2 |
| Self-Seal Foil-Lined Bag · M | 24 × 24 × 15 cm | 240 × 240 × 150 | 9.45 × 9.45 × 5.91 | 9 1/2 × 9 1/2 × 5 7/8 |
| Gusseted Non-Woven Shopper · STD | 40 × 35 × 15 cm | 400 × 350 × 150 | 15.75 × 13.78 × 5.91 | 15 3/4 × 13 3/4 × 5 7/8 |
| Gusseted Non-Woven Shopper · EVENT | 36 × 43 × 10 cm | 360 × 430 × 100 | 14.17 × 16.93 × 3.94 | 14 1/8 × 16 7/8 × 3 7/8 |
What happens when the eighth-inch display is converted back?
Difference = rounded eighth-inch value × 25.4 minus source millimetres. Signed differences below are calculated from the display conversion. They are not observed sample measurements or manufacturing tolerances.
| Style · variant | Dimension | Source mm | Nearest eighth inch | Back-converted mm | Difference mm |
|---|---|---|---|---|---|
| Non-Woven Takeaway Bag · M | Width | 230 | 9 | 228.600 | -1.400 |
| Non-Woven Takeaway Bag · M | Height | 250 | 9 7/8 | 250.825 | +0.825 |
| Non-Woven Takeaway Bag · M | Depth | 140 | 5 1/2 | 139.700 | -0.300 |
| Self-Seal Foil-Lined Bag · M | Width | 240 | 9 1/2 | 241.300 | +1.300 |
| Self-Seal Foil-Lined Bag · M | Height | 240 | 9 1/2 | 241.300 | +1.300 |
| Self-Seal Foil-Lined Bag · M | Depth | 150 | 5 7/8 | 149.225 | -0.775 |
| Gusseted Non-Woven Shopper · STD | Width | 400 | 15 3/4 | 400.050 | +0.050 |
| Gusseted Non-Woven Shopper · STD | Height | 350 | 13 3/4 | 349.250 | -0.750 |
| Gusseted Non-Woven Shopper · STD | Depth | 150 | 5 7/8 | 149.225 | -0.775 |
| Gusseted Non-Woven Shopper · EVENT | Width | 360 | 14 1/8 | 358.775 | -1.225 |
| Gusseted Non-Woven Shopper · EVENT | Height | 430 | 16 7/8 | 428.625 | -1.375 |
| Gusseted Non-Woven Shopper · EVENT | Depth | 100 | 3 7/8 | 98.425 | -1.575 |
Inquiry line fields: style; variant; source W × H × D; source unit; derived unit; rounding method; requested quantity and colour; finished pack dimensions; offered drawing revision; sample measurement record.
How should a non-woven bag size chart show centimetres and inches?
Keep the catalogue dimensions in their original units and put the converted values in separate columns. Name the dimension order on both columns: width × height × depth for the gusseted references used here. Divide centimetres by 2.54 to obtain inches. Label the displayed precision, such as two decimal places or the nearest eighth of an inch, so a reader can distinguish the source measurement from its rounded equivalent.
For example, JINYU takeaway shopper M is listed as 23 × 25 × 14 cm. Its decimal-inch display is 9.06 × 9.84 × 5.51 inches when rounded to two decimals. Keep 23 × 25 × 14 cm on the inquiry line as well. The conversion supplies another reading of the same catalogue body dimensions; it does not create a different stock size or describe the usable interior.
Why keep a millimetre master when comparing rounded inch sizes?
Multiplying the source centimetres by ten gives an exact unit conversion to millimetres without introducing display rounding. Takeaway shopper M therefore has a 230 × 250 × 140 mm source-unit equivalent. Use those values when comparing an offered drawing with the catalogue reference. Retain the style and variant beside them: a string of dimensions alone loses the bag construction and closure information.
A two-decimal inch value can change when converted back. The displayed 9.06 inches becomes 230.124 mm, rather than the original 230 mm. That 0.124 mm difference comes from rounding the unit display. It is not a measured difference between two bags and is not a manufacturing tolerance. Keep the original dimension as the calculation input when a worksheet is copied between teams.
How much can rounding to the nearest eighth of an inch change a chart?
Round the inch value to a multiple of one eighth only in the display column. For a 23 cm width, 230 ÷ 25.4 gives about 9.0551 inches; the nearest eighth is 9 inches. Converted back, 9 inches equals 228.6 mm, which is 1.4 mm below the source value. For the 14 cm depth, the nearest eighth is 5 1/2 inches, or 139.7 mm, 0.3 mm below the source.
The audit table shows the signed difference for each selected catalogue dimension. A positive result means that the rounded inch display converts back above the source millimetres; a negative result means it converts back below them. These arithmetic differences describe the display method. Ask for actual dimensional tolerances against the offered bag drawing as a separate specification.
Can a rounded inch size establish that my box will fit?
Use the original bag dimensions to shortlist a reference, then compare the finished pack with the usable interior and opening. Outside body dimensions do not measure seam intrusions, lining, the closure area or the path needed to insert a rigid box. Include the box lid, projecting tabs and any outer wrap in the pack measurements. Record which face of the pack will lie across the bag width and which will lie along the depth.
An illustrative 230 mm-wide box and a catalogue 230 mm body width produce a zero numerical difference in that single dimension. They do not establish insertion space. Calling the bag 9 inches wide would instead suggest 228.6 mm and obscure the original comparison. Send the actual pack dimensions and request a sample check against the offered stock reference before treating the shortlist as a fit decision.
How do I compare similar inch labels across different bag styles?
Compare the complete source dimensions and construction, rather than grouping rows by an approximate inch label. Takeaway shopper M is 23 × 25 × 14 cm, while self-seal foil-lined M is 24 × 24 × 15 cm. Both have a variant called M, but their widths, heights and depths differ. The foil-lined style also has an adhesive flap, so its usable closed space needs its own measurement record.
The plain gusset shopper STD is 40 × 35 × 15 cm. It shares the 15 cm catalogue depth with self-seal M while having a different body width and height. Neither a common depth nor the same rounded inch label establishes interchangeable bags. Keep the product link, variant code, material and closure beside the source dimensions whenever rows are regrouped in a purchasing spreadsheet.
What belongs in a dual-unit bag inquiry spreadsheet?
Use one line per style and variant. Include the catalogue centimetres, the millimetre equivalent, the decimal-inch display and its rounding method. Add separate columns for requested quantity, colour, intended contents, offered drawing reference and any observed sample measurements. Keep a changed dimension in a requested-change column so it cannot silently replace the catalogue value used to identify the starting reference.
For small non-woven orders, ask which stock sizes and colours are available against those lines. A converted measurement is not a request for a newly manufactured inch-based size. If the required dimensions differ from the stock offer, state the difference explicitly and ask for the available alternative. Keep a custom canvas tote project on its own construction record rather than assuming a stock non-woven conversion applies to it.
What should JINYU return against a chart with mixed units?
Send the chart to JINYU, Shaanxi Jinyu Kitchenware Co., Ltd. (陕西金宇厨具有限公司), with the style and variant identifiers visible. Ask the response to retain the original source dimensions, identify the offered reference and attach its dimension drawing. If a returned inch value differs, compare the unrounded source units first and record whether the difference comes from display precision, a different measurement endpoint or a different offered bag.
Keep the accepted drawing and sample observations with that same inquiry line. Update derived unit columns from the accepted source value, then regenerate the rounded displays together. This avoids one team retaining an old inch label while another works from a revised centimetre drawing. Handle drop, print area, closure overlap and usable internal dimensions remain separate measurements, each with its own endpoints on the drawing.
Reference sources
- Measure an existing bag sample
- Compare flat and gusseted sizes
- Stock non-woven bag catalogue
- Custom canvas tote bags
- Send the size chart with your inquiry
Regional references support general planning; model-specific specifications come from the published JINYU model tables.