Skip to content
JINYUCOMMERCIAL KITCHEN EQUIPMENT
Menu

Finished dimensions · measurement method · sample record

Custom Bag Inquiry: Dimensions, Tolerances and Sample Measurements

Prepare a custom bag dimension record with defined measurement endpoints, proposed tolerance ranges and a worked sample comparison for width, body height and base depth.

Read the worked dimension record →
Floral-print non-woven shopper with black loop handles beside pink flowers
Non-woven print concept. The measurement example below describes an illustrative custom canvas request.

Worked record: proposed limits and one sample

Buyer example CB-01, sample EX-01. All figures are illustrative centimetres, not catalogue specifications or JINYU standard tolerances. Method M1: empty finished body, width and body height laid flat; base depth measured with the base opened, endpoints marked on the drawing.

Differences compare sample EX-01 with the example's proposed limits. The offer and any accepted limits require their own written record.
DimensionRequested nominal (cm)Proposed ± (cm)Proposed range (cm)Observed (cm)Arithmetic comparison
Outside width38.00.537.5-38.538.4Inside proposed range
Body height, handles excluded42.00.541.5-42.542.60.1 cm above upper limit
Opened base depth10.00.39.7-10.39.8Inside proposed range

Record to retain: project and line · drawing revision · measurement method · proposed and offered limits · sample identifier · observer and date · endpoint photographs · decision on each difference.

How should a custom bag inquiry describe dimensional tolerances?

State the requested finished dimension, its measurement endpoints and any proposed tolerance in separate fields. Width, body height and base depth need their own entries. A drawing marked 38 × 42 × 10 cm describes nominal dimensions, while a tolerance describes the permitted difference around each named dimension. Send the proposed limits as buyer requirements and ask the response to address them against the offered construction. They become a shared specification only when the parties identify the same measurement method and accepted limits.

The worked record below uses an illustrative canvas tote request. Its numbers are purchasing examples, not published JINYU dimensions or standard tolerances. A stock non-woven reference follows a different starting record: identify the catalogue family and variant, then ask for the offered dimensions and measurement information. Do not transfer a custom drawing's proposed limits onto a stock bag.

Which measurement method should accompany the requested dimensions?

Draw the endpoints on the finished bag outline. For width, identify the two side edges and the height at which the width is taken. For body height, show the top body edge and the bottom reference. State whether a separate handle is excluded. For base depth, show the base opened into the arrangement being measured, including which seams define the endpoints. These annotations make a repeated measurement possible without interpreting an unlabelled photograph.

Record the sample's condition: empty or packed, base opened or folded, and whether the body is laid flat. A filled tote and a flattened tote can present different outlines even when they are the same sample. Keep the method beside the numbers. If a proposed method changes, assign a new method reference and repeat the affected measurements before comparing the records.

How do I calculate a proposed acceptable dimension range?

For a symmetric proposed tolerance, subtract the tolerance from the nominal dimension for the lower limit and add it for the upper limit. In the illustrative record, a requested width of 38.0 cm with a proposed tolerance of ±0.5 cm produces a range of 37.5 to 38.5 cm. Body height of 42.0 cm with the same proposed tolerance produces 41.5 to 42.5 cm. The 10.0 cm base depth uses a separately proposed ±0.3 cm, giving 9.7 to 10.3 cm.

These limits demonstrate the arithmetic; they do not establish what a particular material or construction can achieve. Request a written response to each proposed limit. Keep the original requested value, the offered value and the accepted drawing revision visible together. A revised nominal size requires its own limits rather than reusing the range from the previous drawing.

How should I record sample measurements against those limits?

Give the physical sample an identifier and record each observed measurement with its unit and method reference. In the example, sample EX-01 measures 38.4 cm wide, 42.6 cm high and 9.8 cm deep. Against the illustrative proposed ranges, the width and depth lie inside their respective ranges. The height is 0.1 cm above the proposed upper limit of 42.5 cm. Record that difference against the height field instead of writing a general comment that the bag looks too large.

The comparison concerns one illustrative sample under one stated method. It does not describe a JINYU sample or establish the result for a batch. Attach photographs showing the endpoints, and preserve the original observations when a remeasurement is requested. Record who measured the sample and the date so later measurements can be compared with the same physical reference.

Should handle drop and print position use the body-size tolerance?

Give handle drop its own endpoints and requested limit. A loop's total strap length and its hanging drop describe different measurements, and neither is the bag's body height. Show whether the drop is measured from the top body edge to the inside or outside of the handle, and record the arrangement used. Keep left and right handle observations identifiable where the drawing calls for separate checks.

Artwork placement also needs a separate record. Identify the printed face, artwork revision, printed width and height, and the position relative to named body edges. A body dimension inside its proposed range does not establish an artwork position or a handle attachment position. Ask the proposal to respond to those fields independently. The dimension record can link to the handle and artwork drawings without assigning the body's example limits to them.

What happens when the offered construction changes the measurement?

Retain the original inquiry and add the proposed alternative as a new revision. A changed base construction, lining or top closure can alter which edge provides a useful measurement reference. Ask the reply to identify both the construction change and the dimension or method it affects. Use the revised drawing and a separately identified sample when reviewing the alternative, rather than combining its measurements with photographs of the earlier version.

For example, if the offered tote uses a different top finish, mark the body-height endpoint on that drawing and compare it with the requested endpoint. If the nominal height or proposed limit also changes, record that explicitly. Keep the decision for each difference beside the related drawing reference. This lets the purchasing team identify which specification was selected without reconstructing it from several email descriptions.

What dimension record should I send with the custom bag inquiry?

Send a project reference, bag line identifier, dated construction drawing and measurement-method sketch. Include the requested nominal dimensions, proposed limits, units and the response required for each field. Add the intended contents as a separate record, along with the handle and decoration drawings. For a sample already received, include its identifier, observed measurements and endpoint photographs. Label illustrative requirements and actual observations distinctly.

Address the inquiry to JINYU, Shaanxi Jinyu Kitchenware Co., Ltd. (陕西金宇厨具有限公司). Ask the response to identify the offered dimensions, measurement method and any proposed changes against the same line. Keep the selected drawing, accepted dimension record and physical sample reference together. For stock non-woven bags, begin with the catalogue code and offered stock information; for custom canvas totes, backpacks or travel bags, attach the construction brief defining the requested body.

Send the drawing and dimension record →